『家电维修论坛 163DZ.COM』 - Powered by Discuz! Board

标题: ddr2引脚定义 [打印本页]

作者: jent 时间: 2008-10-11 12:57 标题: ddr2引脚定义

Front
Back
Pin
Symbol
Pin
Symbol
Pin
Symbol
Pin
Symbol
Pin
Symbol
Pin
Symbol
Pin
Symbol
Pin
Symbol
1
VREF
31
DQ19
61
A4
91
VSS
121
VSS
151
VSS
181
VDDQ
211
DM5/DQS14

2
VSS
32
VSS
62
VDDQ
92
DQS5#
122
DQ4
152
DQ28
182
A3
212
NC/DQS14#

3
DQ0
33
DQ24
63
A2
93
DQS5
123
DQ5
153
DQ29
183
A1
213
VSS

4
DQ1
34
DQ25
64
VDD
94
VSS
124
VSS
154
VSS
184
VDD
214
DQ46

5
VSS
35
VSS
65
VSS
95
DQ42
125
DM0/DQS9
155
DM3/DQS12
185
CK0
215
DQ47

6
DQS0#
36
DQS3#
66
VSS
96
DQ43
126
NC/DQS9#
156
NC/DQS12#
186
CK0#
216
VSS

7
DQS0
37
DQS3
67
VDD
97
VSS
127
VSS
157
VSS
187
VDD
217
DQ52

8
VSS
38
VSS
68
PAR_IN
98
DQ48
128
DQ6
158
DQ30
188
A0
218
DQ53

9
DQ2
39
DQ26
69
VDD
99
DQ49
129
DQ7
159
DQ31
189
VDD
219
VSS

10
DQ3
40
DQ27
70
A10/AP
100
VSS
130
VSS
160
VSS
190
BA1
220
RFU

11
VSS
41
VSS
71
BA0
101
SA2
131
DQ12
161
CB4
191
VDDQ
221
RFU

12
DQ8
42
CB0
72
VDDQ
102
NC
132
DQ13
162
CB5
192
RAS#
222
VSS

13
DQ9
43
CB1
73
WE#
103
VSS
133
VSS
163
VSS
193
S0#
223
DM6/DQS15

14
VSS
44
VSS
74
CAS#
104
DQS6#
134
DM1/DQS10
164
DM8/DQS17
194
VDDQ
224
NC/DQS15#

作者: jent 时间: 2008-10-11 12:58

15 DQS1# 45 DQS8# 75 VDDQ 105 DQS6 135 NC/DQS10# 165 NC/DQS17# 195 ODT0 225 VSS
16 DQS1 46 DQS8 76 S1# 106 VSS 136 VSS 166 VSS 196 NC/A13 226 DQ54
17 VSS 47 VSS 77 0DT1 107 DQ50 137 RFU 167 CB6 197 VDD 227 DQ55
18 RESET# 48 CB2 78 VDDQ 108 DQ51 138 RFU 168 CB7 198 VSS 228 VSS
19 NC 49 CB3 79 VSS 109 VSS 139 VSS 169 VSS 199 DQ36 229 DQ60
20 VSS 50 VSS 80 DQ32 110 DQ56 140 DQ14 170 VDDQ 200 DQ37 230 DQ61
21 DQ10 51 VDDQ 81 DQ33 111 DQ57 141 DQ15 171 CKE1 201 VSS 231 VSS
22 DQ11 52 CKE0 82 VSS 112 VSS 142 VSS 172 VDD 202 DM4/DQS13 232 DM7/DQS16
23 VSS 53 VDD 83 DQS4# 113 DQS7# 143 DQ20 173 NC 203 NC/DQS13# 233 NC/DQS16#
24 DQ16 54 NC/BA2 84 DQS4 114 DQS7 144 DQ21 174 NC 204 VSS 234 VSS
25 DQ17 55 ERR_OUT 85 VSS 115 VSS 145 VSS 175 VDDQ 205 DQ38 235 DQ62
26 VSS 56 VDDQ 86 DQ34 116 DQ58 146 DM2/DQS11 176 A12 206 DQ39 236 DQ63
27 DQS2# 57 A11 87 DQ35 117 DQ59 147 NC/DQS11# 177 A9 207 VSS 237 VSS
28 DQS2 58 A7 88 VSS 118 VSS 148 VSS 178 VDD 208 DQ44 238 VDDSPD
29 VSS 59 VDD 89 DQ40 119 SDA 149 DQ22 179 A8 209 DQ45 239 SA0
30 DQ18 60 A5 90 DQ41 120 SCL 150 DQ23 180 A6 210 VSS 240 SA1

作者: jent 时间: 2008-10-11 12:58

Pin Numbers Symbol Type Description
195 ODT0 Input On-Die Termination: ODT (registered HIGH) enables termination resistance internal to the DDR2 SDRAM. When enabled, ODT is only applied to each of the following pins: DQ, DQS, DQS#, RDQS, RDQS#, CB, and DM. The ODT input will be ignored if disabled via the LOAD MODE command.
185, 186 CK0, CK0# Input Clock: CK and CK# are differential clock inputs. All address and control input signals are sampled on the crossing of the positive edge of CK and negative edge of CK#. Output data (DQs and DQS/DQS#) is referenced to the crossings of CK and CK#.
52 CKE0 Input Clock Enable: CKE (registered HIGH) activates and CKE (registered LOW) deactivates clocking circuitry on the DDR2 SDRAM. The specific circuitry that is enabled/disabled is dependent on the DDR2 SDRAM configuration and operating mode. CKE LOW provides PRECHARGE POWER-DOWN and SELF REFRESH operations (all device banks idle), or ACTIVE POWERDOWN (row ACTIVE in any device bank). CKE is synchronous for POWER-DOWN entry, POWER-DOWN exit, output disable, and for SELF REFRESH entry. CKE is asynchronous for SELF REFRESH exit. Input buffers (excluding CK, CK#, CKE, and ODT) are disabled during POWER-DOWN. Input buffers (excluding CKE) are disabled during SELF REFRESH. CKE is an SSTL_18 input but will detect a LVCMOS LOW level once VDD is applied during first power-up. After Vref has become stable during the power on and initialization sequence, it must be maintained for proper operation of the CKE receiver. For proper self-refresh operation VREF must be maintained to this input.
193 S0# Input Chip Select: S# enables (registered LOW) and disables (registered HIGH) the command decoder. All commands are masked when S# is registered HIGH. S# provides for external rank selection on systems with multiple ranks. S# is considered part of the command code.
73, 74, 192 RAS#, CAS#, WE# Input Command Inputs: RAS#, CAS#, and WE# (along with S#) define the command being entered.
54 (2GB), 71, 190 BA0, BA1, BA2 (2GB) Input Bank Address Inputs: BA0–BA1/BA2 define to which device bank an ACTIVE, READ, WRITE, or PRECHARGE command is being applied. BA0–BA1 define which mode register including MR, EMR, EMR(2), and EMR(3) is loaded during the LOAD MODE command.
57, 58, 60, 61, 63, 70, 176, 177, 179, 180, 182, 183, 188, 196 (1GB, 2GB) A0–A12 (512MB) A0–A13 (1GB, 2GB) Input Address Inputs: Provide the row address for ACTIVE commands, and the column address and auto precharge bit (A10) for Read/ Write commands, to select one location out of the memory array in the respective bank. A10 sampled during a PRECHARGE command determines whether the PRECHARGE applies to one device bank (A10 LOW, device bank selected by BA0–BA1/BA2) or all device banks (A10 HIGH). The address inputs also provide the op-code during a LOAD MODE command.
3, 4, 9, 10, 12, 13, 21, 22, 24, 25, 30, 31, 33, 34, 39, 40, 80, 81, 86, 87, 89, 90, 95, 96, 98, 99, 107, 108, 110, 111, 116, 117, 122, 123, 128, 129, 131, 132, 140, 141, 143, 144, 149, 150, 152, 153, 158, 159, 199, 200, 205, 206, 208, 209, 214, 215, 217, 218, 226, 227, 229, 230, 235, 236 DQ0–DQ63 I/O Data Input/Output: Bidirectional data bus.

作者: jent 时间: 2008-10-11 12:59

6, 7, 15, 16, 27, 28, 36, 37, 45, 46, 83, 84, 92, 93, 104, 105, 113, 114, 126, 135, 147, 156, 165, 203, 212, 224, 233 125, 134, 146, 155, 164, 202, 211, 223, 232 DQS0–DQS8, DQS0#– DQS17#, DM0–DM8 (DQS9– DQS17) I/O Data Strobe: Output with read data, input with write data for source synchronous operation. Edge-aligned with read data, center aligned with write data. DQS# is only used when differential data strobe mode is enabled via the LOAD MODE command. Input Data Mask: DM is an input mask signal for write data. Input data is masked when DM is sampled HIGH along with that input data during a WRITE access. DM is sampled on both edges of DQS. Although DM pins are input-only, the DM loading is designed to match that of DQ and DQS pins. If RDQS is disabled, DQS0–DQS17 become DM0–DM8 and DQS9#–DQS17# are not used.
42, 43, 48, 49, 161, 162, 167, 168 CB0–CB7 I/O Check Bits.
68 PAR_IN Input Parity bit for the address and control bus.
55 ERR_OUT Output Parity error found on the address and control bus.
120 SCL Input Serial Clock for Presence-Detect: SCL is used to synchronize the presence-detect data transfer to and from the module.
101, 239, 240 SA0–SA2 Input Presence-Detect Address Inputs: These pins are used to configure the presence-detect device.
119 SDA I/O Serial Presence-Detect Data: SDA is a bidirectional pin used to transfer addresses and data into and out of the presence-detect portion of the module.
18 RESET# Input Asynchronously forces all registered outputs LOW when RESET# is LOW. This signal can be used during power up to ensure that CKE is LOW and DQs are High-Z.
53, 59, 64, 67, 69, 172, 178, 184, 187, 189, 197, VDD Supply Power Supply: 1.8V ±0.1V.
51, 56, 62, 72, 75, 78, 170, 175, 181, 191, 194, VDDQ Supply DQ Power Supply: 1.8V ±0.1V.
1 VREF Supply SSTL_18 reference voltage.
2, 5, 8, 11, 14, 17, 20, 23, 26, 29, 32, 35, 38, 41, 44, 47, 50, 65, 66, 79, 82, 85, 88, 91, 94, 97,100, 103, 106, 109,112, 115, 118, 121, 124, 127, 130, 133, 136, 139, 142, 145, 148, 151, 154, 157, 160, 163, 166, 169, 198, 201, 204, 207, 210, 213, 216, 219, 222, 225, 228, 231, 234, 237 VSS Supply Ground.
238 VDDSPD Supply Serial EEPROM positive power supply: +1.7V to +3.6V.
19, 54 (512MB, 1GB), 76, 77, 102, 171, 196 (512MB), 173, 174, NC — No Connect: These pins should be left unconnected.
137, 138, 220, 221 RFU — Reserved for future use.

作者: jent 时间: 2008-10-11 13:06

以上表原是ppt格式!但我不想上转附件,故用word转上来,故看有些眼花

作者: 潇洒哥 时间: 2008-10-13 14:08

这个对于普通DIY者没有什么作用。

欢迎光临『家电维修论坛 163DZ.COM』 (http://w.163dz.com/bbs/)

Front								Back
Pin	Symbol	Pin	Symbol	Pin	Symbol	Pin	Symbol	Pin	Symbol	Pin	Symbol	Pin	Symbol	Pin	Symbol
1	VREF	31	DQ19	61	A4	91	VSS	121	VSS	151	VSS	181	VDDQ	211	DM5/DQS14
2	VSS	32	VSS	62	VDDQ	92	DQS5#	122	DQ4	152	DQ28	182	A3	212	NC/DQS14#
3	DQ0	33	DQ24	63	A2	93	DQS5	123	DQ5	153	DQ29	183	A1	213	VSS
4	DQ1	34	DQ25	64	VDD	94	VSS	124	VSS	154	VSS	184	VDD	214	DQ46
5	VSS	35	VSS	65	VSS	95	DQ42	125	DM0/DQS9	155	DM3/DQS12	185	CK0	215	DQ47
6	DQS0#	36	DQS3#	66	VSS	96	DQ43	126	NC/DQS9#	156	NC/DQS12#	186	CK0#	216	VSS
7	DQS0	37	DQS3	67	VDD	97	VSS	127	VSS	157	VSS	187	VDD	217	DQ52
8	VSS	38	VSS	68	PAR_IN	98	DQ48	128	DQ6	158	DQ30	188	A0	218	DQ53
9	DQ2	39	DQ26	69	VDD	99	DQ49	129	DQ7	159	DQ31	189	VDD	219	VSS
10	DQ3	40	DQ27	70	A10/AP	100	VSS	130	VSS	160	VSS	190	BA1	220	RFU
11	VSS	41	VSS	71	BA0	101	SA2	131	DQ12	161	CB4	191	VDDQ	221	RFU
12	DQ8	42	CB0	72	VDDQ	102	NC	132	DQ13	162	CB5	192	RAS#	222	VSS
13	DQ9	43	CB1	73	WE#	103	VSS	133	VSS	163	VSS	193	S0#	223	DM6/DQS15
14	VSS	44	VSS	74	CAS#	104	DQS6#	134	DM1/DQS10	164	DM8/DQS17	194	VDDQ	224	NC/DQS15#